LXC_설정.pptx


'linux' 카테고리의 다른 글

virtualbox 사용법  (0) 2013.03.07
cpu clock(속도) 조절  (2) 2013.03.04
opensource 정보  (0) 2012.05.18
IPv4 packet forwarding  (0) 2012.05.03
리눅스 콘솔내용을 시리얼로 출력해서 보려면  (0) 2012.04.03
블로그 이미지

김유석0

,

coreboot

development 2016. 5. 13. 10:28

Coreboot


바로 빌드 가능하도록 팩키지로 만들었습니다.

Let free use.

rangeley_coreboot_build.tar.bz2



ENV

  platform : Atom C2000 rangeley

  EVB : Mohon peak CRB



필요 팩키지


1. Intel FSP package

  Intel 에서 배포하는 펌웨어 팩키지입니다.

  FSP 는 Firmware Support Package 의 약자입니다. 

 

  FSP 는 x86 cpu 를 초기화 하는 펌웨어 바이너리와 microcode 가 헤더 형태로 제공 됩니다. coreboot 같은 bios 용 SW 들은 빌드 단계에서 microcode 를 참조하고 링크 단계에서 펌웨어를 가져다 사용하기 때문에 반드시 필요합니다.


 

2. coreboot source

  HomePage : https://www.coreboot.org/

  WIKI : https://ko.wikipedia.org/wiki/%EC%BD%94%EC%96%B4%EB%B6%80%ED%8A%B8

  BUILD HOW-TO : https://www.coreboot.org/Build_HOWTO


  Coreboot 는 x86  에서 BIOS 를 대신할 수 있는 opensource 프로젝트입니다.



Worklog


1. Intel FSP

  다운로드 : http://www.intel.com/content/www/us/en/intelligent-systems/intel-firmware-support-package/intel-fsp-overview.html

 

  다운로드 사이트에 들어가 보면, intel 에서 판매하는 여러 cpu 들의 목록이 나옵니다. 이 중에서 원하는 cpu 의 링크를 따라 가면 됩니다.

  

  제가 사용할 플랫폼은 atom rangeley 여서 관련 FSP 를 다운로드 받았습니다.


  fsp(333407_RANGELEY_POSTGOLD_4_001US.tgz) 를 다 받았으면 아래와 같이 압축을 풀어 줍니다. 


poplinux@raw FSP $ > ls

333407_RANGELEY_POSTGOLD_4_001US.tgz


poplinux@raw FSP $> tar zxvf 333407_RANGELEY_POSTGOLD_4_001US.tgz RANGELEY_POSTGOLD_4.se

Readme_Extract.txt


poplinux@raw FSP $ > ls

333407_RANGELEY_POSTGOLD_4_001US.tgz

RANGELEY_POSTGOLD_4.se

Readme_Extract.txt


  압축을 풀고 난 후, 아래와 같이 ./RANGELEY_POSTGOLD_4.se 를 실행하면 압축이 추가로 풀리면서 필요한 파일을 얻을 수 있습니다. 

  자세한 내용은 ./Readme_Extract.txt 를 읽어 보면 됩니다.


poplinux@raw FSP $ > cat Readme_Extract.txt

Readme Notes on how to extract the contents of the *.se file in Linux: 


1.             Run the following command to make the *.se file executable


                chmod +x .se


2.             Run the following command to extract the contents of the *.se file


                 ./<filename>.se


3.             Page through the license using the space bar. At the end enter 'y'

and press ENTER to accept the license. 


4.             The contents of the *.se file will be extracted into a directory with the same name as the *.se file (without the .se extension).


poplinux@raw FSP $> chmod 777 RANGELEY_POSTGOLD_4.se

 

poplinux@raw FSP $ > ./RANGELEY_POSTGOLD_4.se 


poplinux@raw FSP $ > ls

333407_RANGELEY_POSTGOLD_4_001US.tgz

./RANGELEY_POSTGOLD_4

RANGELEY_POSTGOLD_4.se

Readme_Extract.txt 


poplinux@raw FSP $ > cd RANGELEY_POSTGOLD_4


poplinux@raw RANGELEY_POSTGOLD_4 $ > ls

./DOCUMENTATION

./FSP

FSP Kit Production RULAC click-through License.pdf

./Microcode

ReadMe.pdf

 


압축 해제를 완료하면 몇가지 파일과 디렉토리가 생성되는데, ./FSP ./Microcode 가 가장 중요합니다. 


./FSP/RANGELEY_POSTGOLD4_FSP_004_20150924.fd => 펌웨어

./Microcode/microcode-m01406d000e.h => 마이크로 코드

./Microcode/microcode-m01406d8128.h => 마이크로 코드


펌웨어와 마이크로 코드들은 coreboot 에서 직접 가져다 사용하게 됩니다.



2. coreboot

2-1. 소스 준비


  빌드 준비는 아래와 같이 진행합니다.


# 빌드 환경 준비

poplinux@raw work $ > sudo aptitude install gnat-4.8 libncurses5-dev m4 bison flex iasl build-essential zlib1g-dev libftdi-dev pciutils-dev libusb-dev libpci-dev


# git 소스 다운로드

poplinux@raw work $ > git clone http://review.coreboot.org/coreboot.git ./coreboot


# 추가 모듈 다운로드

poplinux@raw work $ > cd coreboot

poplinux@raw work $ > git submodule update --init --checkout

Submodule 'arm-trusted-firmware' (http://review.coreboot.org/arm-trusted-firmware.git) registered for path '3rdparty/arm-trusted-firmware'

Submodule '3rdparty' (http://review.coreboot.org/blobs.git) registered for path '3rdparty/blobs'

Submodule 'vboot' (http://review.coreboot.org/vboot.git) registered for path '3rdparty/vboot'

Submodule 'util/nvidia-cbootimage' (http://review.coreboot.org/nvidia-cbootimage.git) registered for path 'util/nvidia/cbootimage'



2.2 컴파일러 준비

  컴파일러는 아래와 같이 준비 합니다. 빌드 시간은 한참 걸립니다.


poplinux@raw coreboot $ > make crossgcc-i386

Welcome to the coreboot cross toolchain builder v1.39 (April 16th, 2016)


Target architecture is now i386-elf

Downloading tarballs ...

 * gmp-6.1.0.tar.xz (cached)



2.3 설정

  아래와 같이 rangeley 를 위한 설정을 합니다.

 

poplinux@ raw coreboot $ > make menuconfig

   Mainboard  --->

        Mainboard vendor (Intel)  --->

        Mainboard model (Mohon Peak CRB)  --->

        [*] Configure defaults for the Intel FSP package

       ROM chip size (2048 KB (2 MB))  --->


   Chipset  --->

        Include CPU microcode in CBFS (Include external microcode header files)  ---> (../intel/cpu/rangeley/microcode/microcode-m01406d000e.h ../intel/cpu/rangeley/microcode/microcode-m01406d8128.h) 

        -*- Use Intel Firmware Support Package

        (../intel/fsp/rangeley/FvFsp.bin) Intel FSP binary path and filename (NEW)


  Generic Drivers  --->

        -*- Use Intel Firmware Support Package

        (../intel/fsp/rangeley/FvFsp.bin) Intel FSP binary path and filename (NEW)


Mainboard  --->

  Mainboard vendor (Intel) : Intel 로 설정함

  Mainboard model (Mohon Peak CRB) : Intel EVB 이름이 "Mohon Peak CRB" 임

  [*] Configure defaults for the Intel FSP package : Intel FSP 사용하는 것으로 설정함.

  ROM chip size (2048 KB (2 MB)) : 최종 이미지 사이즈를 결정하는 것인데, 이 설정이 잘못되어서 부팅이 안되는 경우가 있습니다.

 

  다른 Embedded 제품들은 flash memory 0x00 번지부터 BIOS(or bootloader) 코드가 위치하는 것을 기본으로 하고 있는데 x86 은 flash memory 의 마지막 부분에 BIOS(or bootloader) 가 존재하는 것을 기반으로 하고 있습니다. 


  예를 들어, flash memory 16MByte 크기이고 coreboot 를 2MB 사이즈로 빌드했아며 coreboot 는 0x00 이 아니라 0xE00000(14Mbyte) 에 write 해야 합니다.


Chipset  --->

  Include CPU microcode in CBFS (Include external microcode header files)  : intel FSP 중에서 microcode 의 위치를 지정해 줍니다. 


  -*- Use Intel Firmware Support Package : intel FSP 중에서 firmware 의 위치를 지정해 줍니다. intel FSP 압축을 풀면 "RANGELEY_POSTGOLD_4/FSP/RANGELEY_POSTGOLD4_FSP_004_20150924.fd" 가 생기는데 이 경로를 상대 경로로 지정해 주면 됩니다.


Generic Drivers  --->

  -*- Use Intel Firmware Support Package : intel FSP 중에서 firmware 의 위치를 지정해 줍니다. intel FSP 압축을 풀면 "RANGELEY_POSTGOLD_4/FSP/RANGELEY_POSTGOLD4_FSP_004_20150924.fd" 가 생기는데 이 경로를 상대 경로로 지정해 주면 됩니다.


2.4 빌드


  아래와 같이 빌드를 진행합니다.


poplinux@ raw coreboot $ > make


Performing operation on 'COREBOOT' region...

Name                        Offset       Type           Size 

cbfs master header        0x0          cbfs header   32

fallback/romstage          0x80        stage           24348

config                        0x6000     raw             452 

revision                      0x6200     raw             570 

cmos_layout.bin            0x6480     cmos_layout   1316 

fallback/dsdt.aml           0x6a00     raw             8074 

payload_config             0x8a00     raw             1574 

payload_revision           0x9080     raw             244 

(empty)                      0x91c0     null             27864

mrc.cache                   0xfec0      mrc_cache     65536 

cpu_microcode_blob.bin  0x1ff00     microcode     167936 

fallback/ramstage          0x48f80    stage           48158 

fallback/payload            0x54c00   payload        61326 

(empty)                      0x63c00    null             1163928 

fsp.bin                       0x17fec0   fsp              389120 

(empty)                      0x1def00   null             133528

bootblock                   0x1ff8c0    bootblock     1528 

          HOSTCC cbfstool/rmodtool.o

          HOSTCC cbfstool/rmodtool (link) 


Built intel/mohonpeak (Mohon Peak CRB)


poplinux@ raw coreboot $ > ls -lah build/coreboot.rom

-rw-r--r-- 1 poplinux develp 2.0M  5월 13 14:03 build/coreboot.rom



최종 생성 이미지는 build/coreboot.rom 입니다.





'development' 카테고리의 다른 글

How to use serial console on Intel rangeley platform  (0) 2016.03.18
How to install ubuntu to rangeley  (1) 2016.01.21
[gcc] -march, -mtune 옵션  (0) 2016.01.08
[gcc] __attribute__((......)) 키워드  (0) 2016.01.06
openwrt  (0) 2015.02.24
블로그 이미지

김유석0

,

환경

  Platform : Intel Rangeley

  Board : Mohon Peak CRB Alpha 3

  OS : ubuntu 14.04.3 LTS 


serial port 를 콘솔 포트로 사용하려면 총 3 군데에 설정을 해야 합니다.


  1. GRUB 동작시 시리얼 포트로 출력하게

  2. 커널 로딩시 시리얼 포트로 출력하게

  3. 커널 로딩 완료후 로그인 쉘을 시리얼 포트로 출력하게

  

  x86 플랫폼에서는, 첫번째 시리얼 포트가 ttyS0 가 아니라 ttyS1 인 경우가 많습니다.

  웹에 올라와 있는 설명들은 ttyS0 가 첫번째 시리얼이라고 가정하고 작성된 문서가 많습니다. 



GRUB 설정 & 커널  설정

  GRUB 화면을 시리얼로 보려면 아래와 같은 설정 추가가 필요하다.


GRUB_TERMINAL=serial

GRUB_SERIAL_COMMAND="serial --speed=115200 --unit=0 --word=8 --parity=no --stop=1"


커널 로그를 시리얼로 보려면(kernel cmdline 으로 전달됨) 아래와 같은 설정 추가가 필요하다.


    GRUB_CMDLINE_LINUX_DEFAULT="console=ttyS1,115200n8"



$ > sudo vi /etc/default/grub


# If you change this file, run 'update-grub' afterwards to update

# /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=2 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="console=ttyS1,115200n8" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) ## Serial console GRUB_TERMINAL=serial GRUB_SERIAL_COMMAND="serial --speed=115200 --unit=0 --word=8 --parity=no --stop=1" # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"



$ > sudo grub-mkconfig -o /boot/grub/grub.cfg



로그인 쉘을 시리얼로 보려면 

/etc/init/ttyS1.conf 를 추가한다.


$ > vi /etc/init/ttyS1.conf


# ttyS1 - getty # # This service maintains a getty on tty6 from the point the system is # started until it is shut down again. start on runlevel [12345] and not-container stop on runlevel [!12345] respawn exec /sbin/getty -L 115200 ttyS1 vt102



$ > sudo start ttyS1 => 바로 동작됨

$ > reboot => 재부팅후 자동 동작됨




'development' 카테고리의 다른 글

coreboot  (2) 2016.05.13
How to install ubuntu to rangeley  (1) 2016.01.21
[gcc] -march, -mtune 옵션  (0) 2016.01.08
[gcc] __attribute__((......)) 키워드  (0) 2016.01.06
openwrt  (0) 2015.02.24
블로그 이미지

김유석0

,